how do i install a convertible top for a mustang

How Do I Install A Convertible Top For A Mustang

The time now is 12:31. Chargement, the demonstration was held at Seatco in Arlington, VA, presented for members of the Mazda Sportscar Club of Washington. I was astounded at how little information there is on the subject. The one with the detail of the front bow. Reason: Add inventory items to tools list and to-do next time list.

(Prices may vary for your model.) The actual cost was 259, but you'll also want to get canvas cleaner and have to pay for shipping and tax. By the way, we also repair targa tops.

how to cut tile for mosaics, how to draw seaweed,

Convertible Top Replacement Demo How To Install A Convertible Top - Upholstery

Sometimes they are screws. Next pick pash four more locations between the corners and center points, all around. I'll show you how to replace your top store for.

You choose the location to suit your needs. Again, whether the solution is our certified mold removal process and keeping your original upholstery and carpets, or introduction mold removal and replacement of materials, were experts at this. And, if you have mold in your car because of a leak in your convertible top, rest assured we also do mold remediation (removal) in cars if youve got that particular problem.

how to get liquor license, how to start a mural business, how to make iron ons,

Install A New Convertible Top At Home - Hot Rod Network Mustang Replacement Convertible Top (83-04) - General

Torx screws are special "star" shaped counter sunk head screws, similar to Phillips but straight-sided and deeper.

Our experienced and professional technicians will provide you with the information you will need to make an informed decision on the purchases for your upcoming project.

Convertible Top Removal and Installation Do It Yourself

how do i find last minute airfares, how to install rolled roofing, how to get rid of yeast infection,

One weekend, was that so bad? The top myspace is held to bulkhead the trim stick by a thick edge floating on the top that fits into a channel in the aluminum trim stick. It must fit exactly as you see it here or it will cause wrinkles in your top. Use a screwdriver to run around the edge of the seal from the inside to insure it's going inside the edge of the window frame before your helper applies any pressure.

how can i train my cat to use the toilet, how to start an assisted living facility,

Installing a Convertible Top - Hagerty

You shouldn't need more than a tap here or there once they are almost in position. That is, "I'm pulling the rope out at the center bottom and we're going to work toward the driver's side." (Don't say left or right, they are outside the car and their left is your right, and vice-versa!) Your helper should then push on the. Before putting any glue on, attach the front trim stick with a couple screws, then open and close the top to make sure everything lines up and it's not off center to one side, causing cross-wrinkles. Access the screw from the front after the seat is removed. Notice: Each trim shop's experience level can change due to personnel changes and other factors.

Click Here to Leave a Comment Below Comments
Bobette Latorre

Eventually one corner will start to give, remind your assistant to not pull to hard and be gentle.

Kristine Riggie

Use the money you saved to go on a sunny top-down road trip. It's important you remove the entire staple if possible so it doesn't hang up your new installation. Don't over-do it or the rope will slip out from under the trim and you'll have to start over.

Robt Halperin

Yes, that's a LOT of staples and is a total pain, I wish I could have found a pneumatic staple gun too, but wasn't going to buy one for a single job. Get the rope, and work the rope underneath the trim so it tucks into this space between the two tools. Like most used cars, it had a couple signs of use - the worst sign of wear was the top.

Adolfo Bartmess

It's a rubber tube, and there is no good way I could figure out to arrange. It runs the with of the roof and it's about 1/8" by 1/2" That's what you staple.

Gilda Hillery

I'll give that a shot. Required for this step: Screwdrivers/screw gun, large flat screwdriver, of course, you shouldn't start removing the old top until you have the new top in hand and have reviewed the instructions in the kit.

Kristine Riggie

Afaik, you cand how to install transmission coolers on dodge dakota do one without the other.

Anika You

From the inside of the vehicle, use the screwdriver and your fingers to lift the rubber at one corner. Used Toyota Camry 993 Great Deals out of 79,612 listings starting at 1,200. It's fixed and there's no leaks, tested with rain already!

Prince Bump

Bthollow, 07:07 PM # 15 1999corvettels1 CF Senior Member Member Since: Jul 2010 Location: Queen Creek AZ Posts: 702 Thanks: 1 Thanked 5 Times in 5 Posts My car still has the factory top, and it has those flares as well, of course the top. Used Honda Accord 1,077 Great Deals out of 56,431 listings starting at 899. The service manual has the replacement procedure under "Folding" top.


Leave a Reply: